Gebrik | Insulated Brick Cladding System

Diverse Sizes and Finishes in Brick Slip Cladding, Enriched by the Integration of the Gebrik Brick Slip System

Gebrik is a unique, innovative, panelised, insulated brick slip cladding system, which is suitable for use on buildings below 11m. It consists of approximately 700 different natural clay brick finishes, in a range of sizes, which are cast in polyurethane under factory-controlled conditions.

With a fire rating of B, s1, d0, the non-load-bearing, lightweight stretcher, stack or Flemish bond cladding panels are produced to create approximately 1m² ‘sheets,’ which can be screwed directly to either masonry, timber or steel frame substrates on site. With a full range of factory-produced or site-applied components to suit external corners, surrounds to window or door openings and any other abutments, the system is restricted only by the architect’s imagination when it comes to design.

Gebrik Fixings

Gebrik can be applied to many substrates, including clay or concrete masonry, light gauged steel frame walling or timber frame walling, using the appropriate quantity and type of fixings. The brick slip cladding system is applied to a solid background so where either steel or timber stud walling is used, an exterior grade board should first be securely fixed to the vertical studs (typically at 600mm centres) and the Gebrik system can then be applied to the board. The number of fixings for each component depends on the exposure of the building, i.e. typically the height and wind pressure on the finished façade. h = 0 – 11m:use 9 fixings (3 rows of 3) If there is any doubt about the type and length of fixing, please contact our Technical Department for further advice.

Product Warranty

Gebrik is supplied with a ten year insurance-backed product warranty. To ensure its validity, the system can only be installed by suitably qualified installation contractors, using all components supplied as part of the Gebrik system. Please contact our Commercial Department to obtain an appropriate list of installers and a copy of the insurance document.

Brick Slip Cladding that exhibits outstanding Thermal Performance

Gebrik is designed to improve the thermal performance of a building and uses expanding polyurethane (PUR), with pentane as the blowing agent. Hence the insulation is CFC and HCFC free and meets the BREEAM credit POL1 relating to the GWP of blowing agents for insulation. The lambda (λ) value of the insulation can be taken as 0.029 W/mK (min 40mm). The lambda (λ) value of the brick slips can be taken as 0.770 W/mK (min 20mm). The system can be supplied with up to an additional 100mm insulation (in 10mm increments) laminated to each component or fixed through (up to) 100mm additional insulation. Please contact our technical department if you require a U-value calculation including risk of interstitial condensation.

What is Gebrik Cladding?

Gebrik is an insulated brick cladding system. It was originally produced in Belgium in 1982 and since then, has been used across Europe to clad over 30,000 different buildings. In the UK, Gebrik cladding has been in use since 2002. Over 400,000 square metres of Gebrik has been installed on buildings in the UK to create an attractive and effective insulating exterior layer.

Gebrik is completely water resistant. It will protect the exterior of a building against even the harshest weather conditions while still allowing the wall to breathe. Mechanical fixing is used to attach the cladding to the exterior wall. It is suitable for use on most substrates and can be used in both new-build projects and building renovations.

How strong are Gebrik components?

Although not suitable as a structural support, Gebrik cladding has a high compressive strength. It has excellent physical properties, including mechanical strength, dimensional stability, and water resistance. It is also extremely impact-resistant, so it works well as a protective layer on any building exterior.

As Gebrik cladding is mechanically fixed to a building exterior, it is less weather-dependent. It is extremely frost-resistant and can, therefore, be used in almost any climate. Although Gebrik Cladding is completely frost resistant once installed, care should be taken during installation. To ensure that all cement-based adhesive is not too wet, it must be applied at temperatures of at least five degrees.